Sign Up to our mailing list

The Voice of Canada’s growing pellet sector
  • Video: Heating with Wood Pellets

    Heating with wood pellets is an effective way to help in the fight against climate change.

  • Video: Wood Pellet Association of Canada

    Existing coal plants can be cost-effectively repurposed to use wood pellet fuel to help the environment and reduce air pollution.

  • Pellets

    Made from renewable forest byproducts and unmerchantable material, wood pellets from Canada provide a renewable, sustainable fuel source for generations to enjoy. | Read More

  • Sustainable

    Only 9% of the world’s forest are certified. Over 42% of them are in Canada, making it an ideal source for sustainable wood pellets. | Read More

  • Renewable

    WPAC members rely on sawmill waste and forest harvest residuals for the bulk of their fibre supply, allowing 100% resource use. | Read More

  • Fossil Fuel Alternative

    Whether on their own or co-fired with coal, wood pellets provide a lower carbon footprint and renewable energy source. | Read More

  • Innovative

    WPAC continues to support R&D in key wood pellet areas like safety, efficiency, fuel stability, energy content and more. | Read More

belt dryer takeaways
A view of the bed dryer infeed at Pinnacle's Williams Lake, B.C., plant, showing the infeed conveyor and metering bin supplied by Continental Conveyors. Photo courtesy Pinnacle Renewable Energy.

The Wood Pellet Association of Canada (WPAC), in co-operation with the BC Forest Safety Council, WorkSafeBC and media partner Canadian Biomass, held the Belt Dryer Symposium on Nov. 25, 2020. As belt dryers have become more common, the pellet industry has experienced several safety incidents over the past few years. The purpose of the Belt Dryer Safety Symposium was to share the learnings from these incidents and for individual operators to share in-house safe operating procedures with their industry colleagues.

Over 70 participants, including pellet producers, dryer manufacturers, insurance companies, universities, fire detection equipment suppliers and WorkSafeBC, attended the event. The workshop was moderated by Fahimeh Yazdan Panah, WPAC’s director of research and technical director.

The symposium included presentations from all the operators of belt dryers in British Columbia. Steven Mueller, director of health and safety at Pinnacle Renewable Energy, and Nathan Bond, plant superintendent at Skeena Bioenergy, described their dryers, energy systems, the safety incidents they experienced and the results of their post-incident investigations. Jimmy Boudreau, plant manager at Canfor, presented their dryer operating procedures in Fort St. Johns and Chetwynd. Comparisons were done between direct versus indirect energy systems and Bill Laturnus, senior safety advisor at the BC Forest Safety Council, examined the use of process safety bowtie analysis as a means of systematically identifying and managing critical controls.

All the incidents that were discussed had occurred in direct-fired dryer systems. The key learnings from the speakers on some of the potential causes for incidents included:
  • Investigation of some incidents showed that the contributing factor in one incident was believed to be loose debris from cleaning activities picked up in air stream, blown through burner, and ignited before being deposited on fibre mat on belt. Smolder eventually burned through the belt and was then recirculated by air flow igniting further smolders.
  • In another incident, strong belief shared that the recirculation of air was a significant contributor to the build-up of flammable deposits, as well as a prime source of ignition as small bits of material could be blown into the airstream through the burner and redeposited on the dryer bed.
  • Another potential cause included introduction of ignition source in fibre stream, or foreign material entering air intake and being ignited by a burner.
  • Some of the incidents were not primarily dryer incidents but turned into one. One hammermill deflagration incident was likely caused by a foreign object creating sparks within the hammermill, possibly a rock or metal contaminant. All other potential causes were ruled out by investigation. In a conveyor deflagration, the entire system was inspected for possible ignition source, but no cause was identified.
  • In one incident, sparks from the fire were not detected by the spark detection system and the temperature sensors above the belt were not affected by the fire’s heat.
A number of action items were executed to address the findings from these incidents. They included:
  • Engaging professional fire investigators to assist in investigation and provide recommendations
  • Bringing dryer manufacturers’ representatives onsite to review and approve new prevention and mitigation measures
  • Increasing dryer cleaning frequency and improving cleaning practices
  • Adding mesh screens in post burner airflows to catch sparks or debris
  • Increasing dryer purge cycle to clear out ducting before restarting burners
  • Adding additional deluge in recirculating ducting for fire suppression
  • Adding man doors to allow for better cleaning and firefighting access
  • Re-programming fan motors to immediately stop in upset conditions to prevent further circulation of smolders/sparks
  • Re-engineering the air flow ducting and stacks to remove the recirculation air ducting system,
  • Conducting Process Hazard Analysis (PHA) with process safety experts on drying systems during removal of recirculating air system
  • Installing infrared cameras to detect/shut down the dryer if hot spots are found in incoming fibre
  • Resetting HMI to alarm/shutdown/deluge on belt temperature increases
At the end of the symposium, participants decided to form a Belt Dryer Working Group to review the past incidents and lessons learned for safer uses of belt dryers in pellet industry.

Anyone seeking more information or interested in joining the working group should contact Fahimeh Yazdan Panah, WPAC’s director of research and technical development:

Tel: 1-778-990-2656
Email: This e-mail address is being protected from spambots. You need JavaScript enabled to view it

Industry Links

Industry Links

Markets

Markets

Become a Member

Become a Member

Safety

WPAC Safety Committee

To find more information about the WPAC Safety Committee and safety resources, please click here

Power Generation

t

Sustainable power

The vast majority of Canadian wood pellets are made from sawmill residuals - sawdust. The rest are made from the residuals from harvesting operations for sawmills and pulp mills, or low-grade timber from forest industry harvest sites that has no other economic value. Think firewood. Read more...

Breathing easier - pellet emissions vs coal

Sustainability should be top of mind for any company that wants to stay in the game in today’s world.

As important a role as Greenhouse Gas (GHG) emissions play, we also need to focus on noxious emissions versus coal.

Read more...

Industry News

t

  • Shell to produce aviation fuel, naphtha from crops and renewable power

    Germany’s Royal Dutch Shell is planning to produce aviation fuel and naphtha from crops and renewable power, aiming to move away from crude oil. The company’s goal is to increase to commercial scale an electrolysis plant that manufactures fossil-free hydrogen.[…]

    Read more...
  • Quebec companies collaborate on one of Canada’s largest green hydrogen projects

    Two Quebec companies have announced one of the country’s largest green hydrogen injection projects for a natural gas distribution network in the province. Evolugen, the Canadian operating business of Brookfield Renewable, and Gazifère Inc., an Enbridge company, are collaborating to[…]

    Read more...

The Pellet Advantage

Efficient and Plentiful Production

Wood Pellet Association of Canada members are world leaders in the design and operation of modern pellet plants.

Read more...

Innovating our way to a safer, better product

Wood pellets are a safe, reliable modern fuel. But they are still a fuel, requiring care in producing, shipping and storing.

Read more...

Renewable and sustainable? Energy really can grow on trees.

There is no single energy source capable of solving our dependence on fossil fuels. Instead we need to look to a mix of new fuels, including wood pellets.

Read more...

Argus Wood Pellet Index

US$ per metric tonneArgus Wood Pellet Index

We are using cookies to give you the best experience on our website. By continuing to use the site, you agree to the use of cookies. To find out more, read our Privacy Policy.